![TRA6421 Chassis brace, 6061-T6 aluminum (dark titanium anodized)](http://www.bigboyswithcooltoys.ca/cdn/shop/products/6421-252w_512x.jpg?v=1676406992)
TRA6421 Chassis brace, 6061-T6 aluminum (dark titanium anodized)
TRAXXAS
FEATURES: Aluminum construction, gun metal gray in color INCLUDES: Chassis Brace
FEATURES: Aluminum construction, gun metal gray in color INCLUDES: Chassis Brace
This is the Traxxas 3x8mm Right and Left Tunnels and Vent Cover. This Tunnels and Vent Cover is compatible with the Traxxas XO-1.Features:Construct...
View full detailsThis is the Rear Wing with Mounts and Washersfor the Traxxas XO-1 On-Road Car, TRAD45**.FEATURES:Constructed of molded plastic, black in colorINCLU...
View full detailsThese are the red shock springs for the Traxxas Slayer.Features: 2.3 lb/in tension Red coating Includes: Two Shock SpringsRequires: Assembly onto...
View full detailsThese are the Red Shock Springs for the Traxxas Slayer. Features 1.8 lb/in tensionRed coating Includes Two Shock Springs Requires Assembly onto the...
View full detailsThese are optional for the Traxxas Slayer PRO 4x4.Features: 7075-T6 aluminum constructed tubes Red and black in color Fits front or rear Includes...
View full detailsTraxxas pair of 72mm turnbuckles for the Traxxas Slayer 4x4. Assembled turnbuckles with captured rod ends. Steel construction with composite plasti...
View full detailsThis is the Front Bumper and Mount for the Traxxas Slayer Pro 4WD Short Course Nitro RTRFEATURES:Nylon constructionBlack in colorINCLUDES:One Front...
View full detailsThis is the Upper & Lower Right Rear Suspension Arm Set for the Traxxas Slayer Pro.. Features: Nylon construction Black in color Inclu...
View full detailsTraxxas center differential kit for use on the Slayer. From the factory, the differentials are filled with 30K weight silicone diff fluid. This is ...
View full detailsThis is a pair of Traxxas Front Progressive +20% Rate (Yellow Stripe) Springs in White for the Ford Raptor and Slash.
Traxxas 5833 Nerf Bars Low CG Black Traxxas Slash These are the Low CG Nerf Bars in Black for the 1/10 scale 2WD Traxxas Slash. FEATURESPlastic con...
View full detailsThis is the optional Low CG Conversion Chassis from Traxxas. Features: Plastic construction Blue in color Holds battery and electronics as deep...
View full detailsTraxxas motor plate is constructed of blue anodized aluminum. This part holds the motors onto the truck. Requires: Installation on the E-Revo truc...
View full detailsTraxxas 5677A Cover Gear 3x8mm CS Revo (1)This is the Gear Cover for the Traxxas Revo.FEATURESPlastic construction, black in colorFor the single mo...
View full detailsThis is a pack of two replacement Traxxas Beadlock Style Sidewall Protectors. This package also includes mounting hardware. Two rings per package. ...
View full detailsTraxxas Spring/Shock Red Long GTR 4.9 Rate Dbl Ylw Strp Features: Steel construction, red in color 4.9 damping rate with double yellow stripe mark...
View full detailsThis is the Traxxas Retainer Clip. This Retainer Clip is black colored and compatible with the Traxxas E-Revo.Features: Black in color Nylon const...
View full detailsTRA5597 Sway bars (rear) (includes soft, medium, hard)
Traxxas aluminum turnbuckle front toe link features red anodized aluminum construction. Black pre-attached ball links Includes: One aluminum link S...
View full detailsFeatures: Metal Construction, installs in gearbox behind the primary clutch assembly Black in color Includes: (1) Metal Primary Shaft (1) O...
View full detailsThis is a Traxxas Differential Gear Set for the Jato. Includes:2x Output Gears2x Spider Gears1x Spider Gear Shaft
These are the rear suspension tie bars for the Traxxas Nitro Jato Stadium Truck.Features: Aluminum construction that’s blue in colorIncludes: One ...
View full detailsThis is a set of four Traxxas Suspension Down Stop Screws with a 2.5mm Drill Bit for the Jato. All R/C off-road racers want as much ground clearanc...
View full detailsTraxxas set of assembled left or right half shafts are direct replacement parts. Rubber sealed boots. Fully assembled Includes: Two assembled half ...
View full detailsTraxxas Left/Right Caster & Steering Blocks 25 Deg Jato Features: Nylon construction Black in color Includes: One Left and Right 25° Caster ...
View full detailsThese are optional Left and Right 30 Degree Caster Blocksfor the Traxxas Jato.FEATURES:Silver Titanium-anodized 6061-t6 aluminum30-degreeINCLUDES:O...
View full detailsThis is a package of Threaded Ball Studs fromTraxxas for use on the Jato 2.5.These are used for the inner camber link mounting.FEATURES:Hard anodiz...
View full detailsTraxxas chassis is made of high-grade 7075-T6 aluminum construction, in a titanium anodized finish make for a chassis 40% stronger than the stock c...
View full detailsFeatures: Anodized Blue in Color 6061 T6 Aluminum Construction Countersunk Screw Holes Includes: One Blue Aluminum Chassis
This is the Rear Bumperfor the Traxxas Nitro Jato Stadium Truck.FEATURES:Plastic constructionBlack in colorINCLUDES:One Rear Bumper.
This is the Wing Mount Hardware for the Traxxas Jato.FEATURES:Nylon flanged tapered nuts.Blue anodized aluminum countersunk cap head screws.INCLUDE...
View full detailsThis is the replacement Sway Bar Linkage Front for the optionalTraxxas Revo/Revo 3.3 sway bar kit - TRAC5598.FEATURES:Nylon and metal constructionB...
View full detailsWe invite you to join our mailing list to receive specials and promotions.
EMAIL: sales@bigboyswithcooltoys.ca
MISSISSAUGA LOCATION: OR-
TEXT 647-321-1965
Need help ONLINE ?
text online support MESSAGES WILL BE ANSWERED
from 11am to 5pm - EST- 7 DAYS A WEEK
** Response times From senior staff 2 TO 3HRS